1000部啪啪未满十八勿入下载-国产精品第12页-成人免费视频在线观看-大香线蕉伊人久久爱-国产精品成人va在线播放

根據OSHA 標準 1926.451，員工必須檢查剪叉式升降機是否配有適當的護欄系統，以防止工人墜落。如果護欄系統狀況不佳，則必須在操作過程中使用額外的防墜落裝置，例如安全帶。

According to OSHA standard 1926.451, employees must check if a scissor lift has a proper guardrail system in place to prevent workers from falling. If a guardrail system is not in adequate condition, additional fall protection devices must be used during operation, such as a safety harness.

為了防止墜落事故，員工應該：

To prevent fall accidents, employees should:

• 操作剪刀升降機之前，請檢查護欄系統是否到位。

• 只能站在工作平臺上，切勿站在護欄上。

• 保持工作物在容易觸及的范圍內，以避免傾斜離開剪刀式升降機。

• Check to see that a guardrail system is in place before working on the scissor lift.
  

• Only stand on the work platform and never stand on the guardrails.
  

• Keep work within easy reach to avoid leaning away from the scissor lift.

大風、坑洞、斜坡或被其他物體或機器撞擊都可能導致剪叉式升降機不穩定并翻倒。ANSI 標準MH-29-2020規定，員工必須確保剪叉式升降機穩定，并防止任何潛在危險。

High winds, holes, slopes, or getting knocked by another object or machine can cause a scissor lift to be unsteady and fall over. ANSI standard MH-29-2020 states that employees must ensure scissor lifts are stable, protected from any potential hazards.

要穩定剪刀式升降機：

To stabilize a scissor lift:

• 選擇表面堅固、水平的工作地點，遠離可能導致不穩定的危險。

• 僅在天氣良好且風速低于每小時 28 英里的情況下使用室外剪式升降機。

• 請遵循制造商的說明以確保安全移動。

• Select work locations with firm, level surfaces, away from hazards that can cause instability.

• Only use outdoor scissor lifts in good weather conditions, with wind speeds that are under 28 miles per hour.

• Follow the manufacturer’s instructions for safe movement.

如果放置不當，剪叉式升降機可能會翻倒或撞到其他機器，從而導致擠壓和觸電事故。OSHA 標準規定，您必須小心地將剪叉式升降機放置在空曠且有足夠的操作空間的區域。尤其是在電線上工作時，電流可能會從電線產生電弧或跳到升降機或工人身上。

When positioned improperly, scissor lifts can cause crushing and electrocution accidents if they're tipped over or bumped into another machine. OSHA standards state that you must position scissor lifts carefully in clear zones with plenty of room to operate. It's especially when working on electrical lines, where electricity can arc or jump from the power line to the lift or worker.

定位升降機時需要注意以下幾點：

Here are some things to be aware of when positioning the lift:

• 當剪叉式升降機靠近工作現場的障礙物（如固定物體、移動車輛或其他設備）時，請務必小心。

• 實施交通管制措施，防止電梯使用時工人和車輛靠得太近。

• 選擇距離電源（如電線、變壓器、其他電源等）至少 10 英尺且不會造成其他高架危險（如其他公用設施、樹枝、門框、懸垂物等）的工作地點。

  
  

• Be watchful when the scissor lift is near obstructions on the job site, like a fixed object, moving vehicle, or another piece of equipment.

• Implement traffic control measures to prevent workers and vehicles from getting too close while the lift is in use.

• Select work locations that are at least 10 feet away from power sources (like power lines, transformers, other electrical sources, and so on) and that don't pose other overhead hazards (like other utilities, branches, door frames, overhangs, and so on).
  

剪叉式升降機有多種類型，例如電動、越野、氣動、柴油或液壓。找到適合您特定工作現場的剪叉式升降機非常重要，這不僅是為了確保它能滿足您的需求，也是為了保證剪叉式升降機操作員的安全。

Scissor lifts come in a variety of different types, such as electric, rough terrain, pneumatic, diesel, or hydraulic. It's important to find the right scissor lift for your specific worksite, not only to ensure it does what you need but also to keep your scissor lift operators safe.

如果您在戶外工作，越野升降機可能是理想的選擇。如果您在室內進行維護，電動升降機可能是您的最佳選擇。

If you work outdoors, a rough terrain lift is probably ideal. If you're doing indoor maintenance, an electric lift might be your best bet.

在操作剪叉式升降機之前，請務必查看制造商的說明，了解重量限制、負載額定值和伸展限制等詳細信息。超過升降機的負載或伸展能力可能會導致其變得不穩定或翻倒。

Before operating the scissor lift, be sure to check the manufacturer's instructions for details like weight limits, load rating, and reach limits. Exceeding your lift's load or reach capacity can cause it to become unstable or tip over.

開始工作之前，請檢查工作區域的狀況，看看可能會遇到哪些安全隱患。對于室外工地，這可能包括洞、坑、不平坦的地形和天氣狀況。對于室內工地，這可能包括頭頂上的危險、顛簸或其他障礙物。

Before you begin work, examine your work area's conditions to see what safety hazards you might run into. For outdoor worksites, this could include holes, pits, uneven terrain, and weather conditions. For indoor worksites, this could include overhead hazards, bumps, or other obstructions.

OSHA要求您在護欄系統狀況不佳或工人走下升降機時佩戴防墜落裝置。

OSHA requires you to wear a fall protection device when the guardrail system is not in adequate condition or when the worker is walking off the lift.

雖然操作剪叉式升降機時并不總是需要佩戴安全帶，但它是一種很好的個人防護設備 (PPE)，可以在出現問題時用作額外的防墜落保護措施。

While you may not always be required to wear a safety harness while operating a scissor lift, it is a good piece of personal protective equipment (PPE) to use as a failsafe for extra fall protection in case something goes wrong.

OSHA 沒有具體規定要求剪叉式升降機操作員必須持有執照。但是，建議只有經過培訓的工人才允許使用剪叉式升降機。

OSHA has no specific regulations requiring scissor lift operators to be licensed. However, the agency says that only trained workers are permitted to use a scissor lift.

根據 OSHA 指南，雇主為員工提供全面的剪刀升降機培訓，包括操作升降機的正確程序、使用剪刀升降機工作時的現場危險以及如何在剪刀升降機上處理材料。

Under OSHA guidelines, employers provide comprehensive scissor lift training to employees, including the correct procedures to operate the lift, worksite hazards when working on a scissor lift, and how to handle materials on a scissor lift.

如果您已準備好開始下一個項目，那么您來對地方了。霸力機械 提供各種剪叉式升降機，可滿足您所有的設備采購需求。

If you're ready to get started on your next project, you've come to the right place. With a wide variety of scissor lifts to buy, Wemet Lift has all your equipment purchase needs covered.